Atish Chemicals

DESCRIPTION AND USE :
AT-TREAT-578 is a product for use in boilers using either oil or solid fuel.  AT-TREAT-578 reduces smut emission and soot deposits and corrosion clinker and slogging in the boilers. The environmental nuisance of smut emission is greatly reduced or even eliminated
GENERAL SPECIFICATION :
Apperance                  :    Slight greenish colour.
Non-flammable
TREATMENT AND DOSAGE REQUIREMENT :
AT-TREAT-578 should be applied to the furnace as a shot dose, once or twice a day. Continuous application is not desirable. The period between treatments should only be greater than 24 hours in very small installations.
The does is normally one part AT-TREAT-578 to 10,000 parts of fuel, by weight. 5 kg AT-TREAT-578 for 1000 M Ton fuel. Also available in stick (rod) & Bottle packing
5 kg of Fireside additive per 12 Hr. and 1 kg for superheater. (55-75  tons Boiler)
PRODUCTION BENEFITS :
Reduces soot deposits and smut emission.
Minimises fireside corrosion.
Reduce slogging
May be introduced to a fouled boiler to soften fireside deposits.
Form modified ash which has a higher melting point & pH, thus is less sticky & less acidic which in term is less corrosive an more easily removed.

It is a polymer based descalant can remove limescale, pipeline scale, Solar pipe scale remover, Heat exchanger scale remover , Boiler tube scale remover etc

We are one of the leading manufacturers of a comprehensive array of Fireside Suit Eradicators for our customers. These compounds are also known as Slag and Clinker Inhibitor. The Fireside Suit eradicators are used primarily to reduce smut emission & suit deposition. Further, these eradicators also prevent corrosion and slogging in the boiler.
Found very effective results for Ricehusk, Indian Coal, Petroleum Coal (With Corrosion inhibitor), Baggase, Furnace Oil, Petcock as fuel in Boiler.
 
 

Description and use: Hardness in feed water is caused by the presence of calcium and magnesium salt. High hardness is the principle source of scale formation in a variety of processes involving heat transfer, such as boiler feed water heater, feed lines and economizers. Boilers are heavily scaled by precipitation of calcium &magnesium salt.
AT-treat-575 is an inorganic polyphosphate and used for boiler of any pressure, to precipitate calcium hardness as mobile phosphate sludge. AT-treat-575 precipitation of hardness salt in feed lines. It may be injected continuously to feed water containing hardness salts, without the formation of excessive scale in the the pipeline.
General specification :
Appearance : clear to pale yellow liquid
Specific gravity : 1. 1 to 1. 3
pH as supplied :6. 0 to 8. 0
Non-flammable :
Non volatile
Treatment and dosage requirement :
A phosphate reserve is normally maintained in boiler water, within set limits . The correct treatment level depends on operating conditions such as boiler pressure, the chemical characteristics of the water employed. AT-treat-575 can applied directly or diluted (preferably softening water or condensate).
AT-treat-575 is not corrosive to steel mixing tanks or dosage pump,in concentrated or diluted form . However if dosed directly to hot boiler shells, use a stainless steel injection fitting.
Production benefits :
Effective scale inhibitor / dispersant.
May be directly from drum.
Simple on-site control test.
Compatible with complete boiler program.
Potential hazards:
This product is not considered to be harmful, but as with all industrial chemicals care should be exercised in its use.
Spill procedures :
Flush to drain adequate dilution of water. Local effluent regulations must be observed
Handling and storage :
Avoid contact with skin and eyes (s 24/25). Avoid extremes of temperature . Replace cap securely after use. Recommended maximum storage two years. Wear suitable gloves & goggle &face protection.
First aid :
Skin : wash affected area immediately with clean water for at least ten minutes.
Eyes : irrigate thoroughly with clean water for at least ten minutes.
Seek medical attention if irritation persists.
Ingestion : wash out mouth thoroughly and drink plenty of water
Do not induce vomiting. Seek medical attention.
Packing :
In available 35 kg net capacity HEDP carboys.
CPL classes class unclassified. Non hazardous.

Customers can avail from us a premium quality range of Hardness Removers that is also known as Water Softening Agents and Phosphate Builders. These compounds are extremely popular in the market owing to their unmatched purity and efficiency. Hardness causing calcium that is present in the water is removed using these compounds, thereby softening the water and making it fit for use. Additionally, the phosphate level of the water is also maintained using these compounds.

We provide our customers with high quality Catalysed Oxygen Scavengers to our customers. These chemicals are available in various specifications like:
 
• Catalysed Sulphite based
• Catalysed Hydrazine based
• Catalysed Carbohydrazide based
• Catalysed DEHA based
 
These products are extensively used to remove the dissolved oxygen from the boiler water and thus avoid corrosion of the boiler from the inside. These are liquid catalysed oxygen scavengers that are catalysed sulphite based, which react with oxygen instantly. To speed up the reaction, a catalyst is also used. The catalyst is incorporated to speed up the reaction.
The further details of these chemicals see the attached PDF.

Sludge Conditioner or Boiler Antiscalant
Available with us is a premium quality range of Sludge Conditioners that is also known as Boiler Antiscalants. These compounds are Organophosphate LMW Polymer based. The prime usage includes the prevention of iron deposition, calcium carbonate, phosphate, and scale in the boiler that corrodes the interior portions of the boiler tank. We are looking for India query.
The detailed specifications of these compounds are as follows:
 
Description and Uses
 It is a scale and sludge conditioner / dispersant that is designed primarily for steam boiler
 Used to prevent the build-up of deposits or iron and other metallic oxides, originating from corrosion of condensate systems
 It is based on a synergistic blend of dispersant and scale inhibitor
 Works by bonding iron in solution, using a cheleting action and / or (depending on boiler pH) dispersing precipitated metallic salt
 
General Specification
 Appearance clear colorless to pale yellow liquid
 pH :8-9
 Specific gravity: 1.10 तो 1.15
 
 
 
Treatment and Dosage Requirement
 6-9 ppm on feed water
 Correct treatment level for deposit prevention depends on operating conditions, such as pH and the number of concentrations
 Optimum treatment level, for any plant will be specified by us
 Viscosity allows it to be handled by conventional dosing pumps, without dilution
 May be diluted if desired
 Not corrosive to mild steel mixing tank or dosage pumps, in concentrated or in diluted form
 May be pumped directly from container using equipment in steel or plastic
 
 
 
Production Benefits
 
 Inhibits scale formation for boilers
 Low toxicity
 May be dosed direct from drum
 Compatible with a complete boiler water treatment program
 
 
 
Potential Hazards
Not considered to be harmful, but care should be taken in its use
Wear suitable gloves and eye /face protection (S 37/39)
 
Spill Procedures

Flush to drain plenty of water
 
 
Handling and Storage
 Avoid contact with skin and eyes
 Avoid extremes of temperature
 Replace caps securely after use
 In case of contact with skin wash well with soap and water
 In case of contact with eyes wash immediately with plenty of water for at least 10 minutes
 If irritation persists, seek medical attention
 In case of ingestion wash out mouth thoroughly and drink plenty of water
 Do not induce vomiting
 Seek medical attention if discomfort persists
 Recommended maximum storage limit is 2 year
Packing

Available in 35 lit, 50 lit HDPE Carbouy
 

Alkalinity Builder/ PH Booster For Boiler
pH BOOSTER are of different types depends on Boiler Capacity and Pressure. Some are Hydroxy based, Amine based or Mixed (volatile) amine blend.
Description and Use:
AT-TREAT-571 is an alkalinity builder/ pH Booster used for increasing pH and maintaining the correct alkalinity in the boiler water. Alkalinity control is a vital part of any internal boiler water treatment. AT-TREAT-571 is useful for neutralizing any acid pick-up as well as maintenance of correct pH and alkalinity in boiler water.
AT-TREAT-571 is compatible with most chemicals used for total boiler water treatment programs.
General Specification:
Appearance Clear colorless liquid
pH : Highly Alkaline
Specific gravity 1.47 to 1.50
Flammability non- flammable
Active Solids 45-50% Min.
Treatment and Dosage Requirement:
AT-TREAT-571 can be dosed as such or diluted if desired. It may be dosed directly to the feed tank and the product characteristics permit dosing with any conventional on line dosage pump.
The exact dosage will vary with operating conditions and water characteristics. Our engineers shall establish the exact requirement to maintain boiler alkalinity within limits.
The treatment levels normally adjusted as per test for boiler alkalinity.
Product Benefits:
Ready to use liquid product.
Reduces acid corrosion.
Stabilizes protective magnetite film.
Simple monitoring procedure.
Provides alkalinity control.
Facilitates to PO4 & MgOH dispersion.
May be directly used in to boiler without dilution.
Product Safety & Handling Information:
Avoid contact skin and eyes. Keep away from acids. Being a strong alkali it can cause burn. In case of contact with skin , wash with plenty of water. Remove contaminated clothing and seek immediate medical attention. In case of contact with eyes, flush with plenty of water, cover affected eye with sterile pad and seek immediate medical attention. Wear gloves and goggles wherever appropriate.
First Aid :
Skin : Flood area with water for at least 10 minutes. Remove any contaminated clothing. Seek medical attention
Eyes : Irrigate thoroughly with clean water for at least 10 minutes. Cover affected eye with sterile eye pad and seek immediate medical attention.
Ingestion: Wash mouth thoroughly & drink plenty water. DO NOT induce vomiting. Seek immediate medical attention.
Packing: Available in 50 kg net capacity HDPE carboys.

Morpholine Chemical issue in boiler to improve pH of the boiler water.it does not add TDS of the water. it''s neutralizes the Carbonic Acid which is corrosive. Hence keeps the line free from Corrosion it also use in RO System to improve the pH of Water in blend.

Condensate Neutralising Amine (pH BOOSTER)
Description And Use :

Neutralising Amines are high pH chemical that can be fed directly to the feed water or steam header to neutralize the carbonic acid formed in the condensate (acid attak).AT-TREAT-579 distribution ratio is better than that of morpholine, ammonia and other similar amines therefore its efficiency of neutralizing aqueous solution containing CO₂ is better. AT-TREAT-579 can be used at steam pressure up to 163 Bar (2400 psig) and temperature up to 590 ^oC. AT-TREAT -579 provides effective neutralization of acidic gases such as CO₂ in the near end of a condensate system. AT-TREAT-579 reduces corrosive & formation of bearing deposits.

Advantages:

High base strength

Low molecular weight

High boiling range

Low Volatility

Primary amine functionality

Helps for Oxygen Scavenging

Ideal for High to Very High Pressure as pH BOOSTER.

This helps in keeping heat transfer surfaces, steam traps etc. clean & improves boiler efficiency. AT-TREAT-579 reduces concentration of iron, copper and nickel in return condensate water. This reduces fouling of cation, anion resin from condensate polishing unit.

General Specifications :

Appearance: Colorless to Pale Yellow

Density: 0.98 -1.01 gms/ml

Solubility: Soluble in water

pH: 9-11.oo min

Boiling range: 100 -180 0C

Flash point:89 0C

Vapour pressur: 0.2 mm Hg 200 C

Toxicity (oral): LD 50 1360 Mg/Kg rat

Amine Value:350-500:as per requirement

Treatment and Dosage:

AT-TEAT-579 dosage depends upon the feed water quality boiler operating parameters. In general 5-8 ppm dose is adequate in the make water initially. The product should be dosed into the feed water on continuous basis. AT-TREAT-579 is compatible with all conventional boiler feed water treatment chemicals like TSP and non conventional chemicals as well.

CO2 in steam is 0.88 X feed water M alkalinity X (Boiler water P alkalinity/ Boiler water M alkalinity) - (Feed water P alkalinity/Feed water M alkalinity)

Handling and Storage:

Avoid contact with skin and eyes. Wash contact area with plenty of fresh water.Seek medical attention Incase contact with eyes wash thoroughly with clean water at least 10 minutes. In case ingestion wash mouth thoroughly with water &drink plenty of water. DO NOT INDUCE VOMITING. Seek medical attention.

Packing:

Available in standard 30 kg, 50 kg &100 kg/lit HDPE Carboys.

Note : The above information is subject to change without prior notice .